Archive for the ‘Quadcopter’ Category
Seychelles drone footage
Posted: 17th October 2018 by viljem_r in Gopro, Quadcopter, StartTags: dji, drone, mavic, mavic air, nature, seychelles
Kopterworx repair of my phantom 3 gone bad
Posted: 24th May 2016 by viljem_r in Quadcopter, StartTags: bad experience, customers complain, dji, kopterworx, kopterworx shop, not repaired, online shopping, phantom 3, phantom 3 proffesional, remote damaged, rma, rude
Here is my experience with Kopterworx. Kopterworx sells DJI products and repairs them. I had problems with my camera, so I sent them my drone for warranty repair. I sent them by mail packed in original package put in another box, with fragile and mail insurance. They repaired it and sent it to me. The […]
Dji phantom 3 gimbal guard
Posted: 14th December 2015 by viljem_r in Quadcopter, StartTags: camera, DIY, dji, dji phantom 3, gimbal, gimbal guard, guard, phantom, quadcopter
You can make your own gimbal protection in just 10 minutes. It is very usefull when you want to land somewhere on grass or other terrain. It will protect your camera and gimbal. I used old laptop cover for guard, cut it with grinder and sand it with paper. I also drilled some holes to […]
How to clean or disassemble brushless motor
Posted: 30th July 2015 by viljem_r in Quadcopter, Start, Technical stuffTags: 1100kv, brushless motor, quadcopter, r/c, turnigy
Testing Fpv quanum set from hobbyking
Posted: 14th May 2015 by viljem_r in Quadcopter, StartTags: drone, fpv, gopro, hobbyking, quadcopter, quanum set fpv
Here I’m flying fpv with quanum set and Gopro hero 3 black instead off camera in set. Video is shaky and has a lot off jello effect, because I used frame instad off gopro housing. If you are recording while using camera for fpv there is some lag, but you still can fly without any […]
Mini quad with naze32 and fpv, video
Posted: 2nd March 2015 by viljem_r in Quadcopter, StartTags: fpv, mini quad, naze32, racer
Video of testing mini quad-racer for 80 eur with fpv from hobbyking. We used naze 32 controller. It was very windy, but it flew nicely.
Hobbyking HK6S receiver mod 3 position switch for dji naza
Posted: 14th February 2015 by viljem_r in Quadcopter, StartTags: DIY, dji, dji naza, hk6s, naza, quadcopter
Here is video about mod you will need if you are flying with dji naza. You will 3 positions on chanel 6 to select flight modes. Original potentiometer is not good, because it switches modes and it is really hard to select mode. Original has 10k potentiometer. So voltage is 3,3V between brown and orange wire. […]
Naza m-lite upgrade to naza v2
Posted: 9th February 2015 by viljem_r in Quadcopter, StartTags: dji, naza, naza v2, naza-m lite, quadcopter
You can buy naza m-lite with gps for 130 eur and upgrade it with this tool to 240 eur naza v2. Both nazas have same hardware, but different firmware.You can also downgrade it to original firmware, so there is no problem with warranty. Follow this instructions: http://naza-upgrade.com/ Tip: When you try to upgrade it make […]
MegaPirateNg on Hobbyking Multiwii pro simple tutorial
Posted: 9th April 2014 by viljem_r in Quadcopter, StartTags: gps, hobbykingf, megapirate, megapirateng, multiwii, multiwii pro, quadcopter, simple, tutorial
I recently purcashed HK multiwii pro. If you want to change parameters you’ll need to changed them in code with arduino or in multi wii gui. Quite complicated for beginers. Friend told me that this megapirate fw is awesome for this board. You basiclly use simple APM interface for editing multi wii […]
New rc project
Posted: 4th July 2013 by viljem_r in Quadcopter, StartTags: blog, hobbyking, new parts, obby, planes, r/c
Time to build something new… Some parts received, other on the way. If you like my blog you can donate for more cool projects 😉 Tnx